Windows and Door Locks Stopped Working Together? BCM Guide (2026)

As of November 2026, when power windows and door locks stop working together, the cause is usually one shared part: a fuse or relay, a battery or charging event, a faulty door module, or the body control module (BCM). BCM coding or reset typically costs $150 to $350 in Fort Worth, and replacement with programming typically costs $200 to $600, plus the module where one is needed.
The important word is "together." One dead window is almost always a switch or a motor. A window, the locks and the interior lights failing in the same moment is a different pattern, because those systems have something in common, and that is what we diagnose. This guide walks the order of checks, explains what a BCM actually does, and tells you where the free tests end and a module visit begins.
We are a mobile-only service. If the evidence points to a module, we do the scan and any programming where the vehicle is parked, anywhere in Fort Worth and the surrounding Tarrant County area.
Windows and Locks Down Together: Causes, Tests and Costs
Work down the table from the top. The cheap, common causes come first.
| Likely cause | What you notice | Quick test | Typical cost |
|---|---|---|---|
| Blown fuse or failed relay | Windows and locks dead, everything else fine | Check the fuse box diagram for the body circuits | Fuse cost, usually minimal |
| Weak or recently disconnected battery | Problems began after a battery change or a jump | Battery test, check terminals | Battery cost, if needed |
| Window or lock master switch | Driver-door controls dead, passenger switches work | Use each door's own switch | Part cost, small repair |
| Door module or door wiring harness | One door affected, often intermittent | Check the rubber boot between door and body | Wiring repair, shop item |
| BCM needs a reset or relearn | Several functions odd after a battery event | Scan for faults, run the reset procedure | $150–$350 |
| BCM communication or internal fault | Many unrelated functions fail, scan shows no response | Scan every module, check power and ground to the BCM | $200–$600 with replacement |
| Water or corrosion in the module area | Failures after rain, a wet floor or a leak | Inspect the carpet and the module under the dash | Quote after inspection |
The last two rows are where our work begins. The rows above them you can check yourself, usually for little or nothing.
What a Body Control Module Does
The BCM is the vehicle's coordinator for body functions. On many cars and trucks it manages the power locks, interior and exterior lighting, wipers, the horn, the power windows on some models, the key fob receiver, and the security system. It also talks to the other modules over the vehicle network. Because it sits in the middle of so many systems, a BCM problem tends to look like a pile of unrelated problems.
That is why "everything electrical is acting weird" is such a common description of a BCM fault, and why guessing is expensive. If you want the background, our guide to what BCM programming is and when it is needed explains the module in more detail, and BCM programming near me covers the service itself.
Step 1: Check the Fuses and Relays
Find the fuse box diagram in the owner's manual or on the fuse box cover. Look for fuses that feed the power locks, the power windows and the body circuits. Pull each one and look at the filament. A fuse that is blown once may be a fluke. A fuse that keeps blowing means something downstream is shorting, and replacing the fuse again only delays the problem.
If the fuses are good, move on. Do not replace a fuse with a higher-rated one to "fix" it. That removes the protection the circuit relies on.
Step 2: Think About the Battery
Modules need steady power. A battery that is old, weak, recently disconnected or recently jump-started can leave body electronics in a confused state. Some modules lose their settings when power drops and need a relearn afterward. Our guide to a car acting up after a dead battery or jump start covers this pattern, and car says wrong key after battery replacement in fob covers the key side of it.
Ask when the symptoms began. If they started right after a battery event, a reset or relearn may fix them without replacing anything. Test the battery and check the terminals first, because a weak battery can cause these symptoms by itself.
Step 3: Test Each Door Independently
Use the switch at each door, not only the driver's master. If one door's controls work and another's do not, the fault is local to that door: a switch, a motor, a door module or the wiring harness that runs through the flexible boot between the door and the body. That boot flexes thousands of times and is a classic place for broken wires. A door-local fault is not a BCM problem, and it is a good reason to check before spending on a module.
If every door is dead at once, the shared cause becomes more likely.
Step 4: Look for Other Things That Failed at the Same Time
Make a list of everything that stopped. The more unrelated systems are on it, the more likely the BCM or its power supply is involved:
- Interior or dome lights.
- Key fob lock and unlock buttons.
- Horn.
- Wipers or washer.
- Turn signals or hazard lights.
- Security light on the dash.
- Remote start.
A security light that flashes, or a car that now will not start, matters. On many vehicles the BCM takes part in the immobilizer handshake, so a body module fault can interrupt starting. If that is happening, see our guide to a security light flashing with the engine starting then dying and all warning lights on with dead module communication.
Step 5: Scan the Modules
A scan reads fault codes from every module the tool can reach. For a suspected BCM problem, the useful results are:
- The BCM responds and reports faults. The module is alive. A reset, recode or relearn may fix it.
- The BCM does not respond at all. Check power and ground to the module first. If those are good, the module itself or the network may be at fault.
- Several modules report lost communication. The problem is likely on the network or in the power supply, not in one module.
If the scan tool will not connect to the vehicle at all, start with the OBD port and communication guide. The scan is the point at which this becomes a diagnosis instead of a guess, and it is the reason we scan before we quote.
Reprogram, Recode or Replace
When the BCM is the problem, there are three possible outcomes, and they are priced very differently.
Reset or relearn. The module is healthy but has lost its settings. Software only, typically $150 to $350 as of November 2026.
Recode or reprogram. The module needs fresh software or configuration to match the vehicle. Also software work, in the same band.
Replacement. The module is dead, water damaged or no longer communicating. A new or used module is installed and programmed to the vehicle, typically $200 to $600 plus the part, and a replacement can require re-registering keys if the BCM is part of the immobilizer. A BCM and engine module combination sequence is typically $425 to $725.
| Module job | Typical mobile price | When it applies |
|---|---|---|
| BCM coding or reset | $150–$350 | Module responds but behaves oddly |
| BCM replacement with programming | $200–$600 | Module dead or damaged |
| BCM and PCM combination | $425–$725 | Both modules affected |
| Luxury or complex systems | Quote after diagnosis | Proprietary security or networks |
Our guide to BCM programming versus replacement explains how to tell which path applies, used BCM programming to VIN covers the case where a used module is the economical choice, used module programming cost shows the price bands, and dealer versus locksmith module programming compares the routes. For the broader price picture, see car computer module programming cost and module programming near me.
If a new module has already been installed and the car still will not start, read new module installed, car still won't start.
What Moves the BCM Cost
Software versus a part. A reset costs far less than a replacement, because there is no module to buy.
Whether keys are involved. On vehicles where the BCM is part of the security system, a replacement needs the keys re-registered. That is included in the visit, not a separate trip.
New versus used module. A used module can cost less, but it has to be matched to your vehicle, and the work is priced accordingly.
The make and model. Some vehicles are straightforward, and some luxury or complex networks are quoted after diagnosis. We do not promise a number we cannot support.
Water damage. A module that has been wet is often dead, and the leak that caused it has to be fixed first.
When to Call a Professional
Call when:
- Several unrelated body functions failed at once and the fuses and battery check out.
- The problem began after a battery event and a simple reset did not clear it.
- A scan shows lost communication with the BCM.
- The car also shows a security light or will not start.
- Water has been in the cabin and the electronics are now misbehaving.
If a single window or lock is dead, start with the switch or the door. If the car has a general wiring fault outside the modules, a general repair shop is the right place, and we tell you so. Texas locksmith licensing runs through the Department of Public Safety Private Security Program, and our work is mobile, so the diagnosis and any programming happen where the car is. Call (817) 668-3801 or use the contact page.
Frequently Asked Questions
Why did my power windows and door locks stop working at the same time?
A shared cause is likelier than several separate failures. The usual suspects are a blown fuse or relay feeding the body circuits, a battery or charging event that confused the electronics, a faulty door module, or the body control module itself. If interior lights, the horn or the key fob stopped at the same moment, the body control module moves higher on the list.
What are the signs of a failing body control module?
Several unrelated body functions misbehave together: windows, locks, interior lights, wipers, the horn or the key fob. Symptoms come and go, may follow a battery disconnect, and the car can show a security light or fail to start. One failed function alone is rarely the BCM. A cluster of them, especially with a scan showing communication faults, points that way.
Can a dead or replaced battery cause these problems?
Yes. A deeply discharged or disconnected battery can leave a module in a confused state, and some body modules need to relearn settings afterward. If the problems began right after a battery change or a jump start, a reset or relearn may fix it without replacing anything. A weak battery can also cause the symptoms on its own, so test it first.
How much does BCM programming cost in Fort Worth?
As of November 2026, BCM coding or reset, which is software only, is typically $150 to $350. BCM replacement with programming is typically $200 to $600, and a BCM and PCM combination sequence is typically $425 to $725. The module part is separate where one is needed. Luxury and complex systems are quoted after diagnosis.
Do I always need a new BCM?
No. Many body control modules that look dead respond to a recode or reset. A new module is only needed when the unit no longer communicates, has failed internally, or has water or corrosion damage. A proper scan tells you which applies, and we do it before quoting a replacement, so you do not pay for a module you do not need.
Will a new BCM affect my keys?
It can. On many vehicles the BCM takes part in the immobilizer handshake, so a replacement module may need to be matched to the vehicle and your keys re-registered. We handle that in the same visit. If the car fails to start after a module swap, that is a known pattern and is covered in our guide to new modules that leave a car unable to start.
Can you diagnose this at my location?
Yes. We are a mobile-only automotive service and perform the scan, the reset or recode, and the module programming where the vehicle is parked anywhere around Fort Worth. If the fault proves to be a fuse, a wiring problem or a door motor, we say so before any module is touched.